Fire Pots, Clinker Breakers, Swage
Blocks
Roger Lorance (309) 475-9012
09/08
Roller Blade Treadle Hammers
(Clay Spencer design)
for sale or workshops led
to build
these hammers
Bob Alexander (636) 586-5350
scruboak4@netzero.com
07/08
Heinrich mod. 5A punch, shear,
rod parter, hand nibber
( used, but
gently; only on mild steel, and mostly
on sheet-stock). This unit will punch
round or square to 1/2", shear to
3/16", part to 1/2" nibbles inside or
out, again to 3/16 all specs for mild
steel. This is a heavy unit- 60+lbs,
with the swivel base. Comes with a
couple of punch/die sets. Needs 1 set
for each size. Parts are available, as
are punch sets from Heinrich in
Racine, WI. A very helpful device to
have in a shop. $250.00 (700.00 new)
Jeff Rasper (414) 304-7801
ravatar252@gmail.com
03/09
PLASMA-CUT BLANKS
Rose Kits, Leaf Blanks, Rosette Blanks
...Anything you can think of - we can cut!
Rick Medd (563) 242-2226
rmmedd@mchsi.com
01/10
USED BLACKSMITH EQUIPMENT
I probably have it or know
where to get it.
John Biewer (847) 404-4903
anvils3@yahoo.com
09/08
|
B2 Nazel, $18,000
Heat Treating Oven, best offer
Air-Operated Bending Table,$600
250 lb. Anvil $500
Grewe’s Blacksmith Shop, Inc.
920-987-5681 grewe@dotnet.com
09/08
500 lb Bradley
Guided Helve Hammer
Located at the Max Weiss Co.
Milwaukee, WI
Al Sanders 888-649-3477
asanders@maxweiss.com
01/09
Tent -18’ x 24’ All canvas, ropes,
poles, stakes, and boxes they go in,
$2,000.00
Dennis Anderson 563-391-1985
dennisanvil@mchsi.com
09/09
Ray Clontz Tire Hammer Plans
by Clay Spencer
$30.00 US incl. postage
US and Canada
$32.00 to other countries.
Workshops for chapters or groups to
build 15-20 hammers.
Tire Hammers for sale: $2,500.00
~~~~~~~~~~
Beverly Sheared Blades Sharpened
$35.00 plus postage, additional cost
for deep
notches or blades
previously
sharpened at angle.
Remove blades from shear to ship to:
Send check or money order to:
Clay Spencer
73 Penniston Private Drive
Somerville, AL 35670
clay@otelco.net
07/09
|
BLACKSMITH TOOLS
Fulton 100 lb. Anvil
Forge with a hand blower
Two four in. blacksmith vises
Two small arbor presses
Two nail or rivet makers
12 Shaping hammers
25 Tongs
Two water ladels
Small amount of coal
Large welding table
$1500.00
Wayne Blount
1512 F St. Amana, IA
52203-8083
03/09
Heavy-Duty Fry Pan Blanks
9” diameter, tapered sides
12 or 13 gauge sheet steel (approx. 2 lbs.), no
pre-drilled holes for the handle.
$10.00 each……….. 1-4
$9.00 each……….. 5-9
$8.00 each……….. 10 +
Shipping:
$5.00 plus $.75/each fry pan blank
Bob Tuftee
563-332-4800
3855 Aspen Hills Drive
Bettendorf, IA 52722
bobforge@hotmail.com
09/09
Tongs, Texture Tools, Spring
Swages, and more from
Off-Center Forge (Grant Sarver)
Dave Brandon 815-359-4378
11/08
|
